PELLETS.INFO

Well, I am not sure if there was a problem with the light sensor. It is quite possible all the problems were related to the feeding of the pellets. I took out the auger, dismanteled the tube and cleaned all.. now pellets feeding is back to mormal and the burber has been working flawlessly for the pa...

Well.. i hope I am too annoying with my questions :) Fan is replaced and I thought my problems are over, but alas - not. The new fan is working ok, so no problems there, but I have starting problem now. Symptoms are as follows: - feeding with pellets is OK (max dose) - after a while flame starts (it...

Thank you once again. I think the downpipe overheated this year, because my father started the burner with clogged chimney and turbulators. I did clean everything afterwards and it usually never heats. The chimney is about 12.5 height, and the draught regulator opens quite often even though it is se...

By the way, while I am waiting for the new fan to come from Sweden, I was wondering if I need to change the adapter for the CTC. The tube of the burner barely enters the chamber.. no more than 1-2 cm inside. Do I need to shorten the adapter so the burner enters more in? see here: https://www.dropbox...

Hi, thank you for the information about the switches. The problem turned out to be the Fan. It has some blown transistors inside the fan's board (visible). A friend of mine will try to repair it tomorrow. If the processor chip is fine, he should be able to repair it If not, I will order one from Swe...

https://www.dropbox.com/s/kwqhw0zu283dyee/2014-11-29%2010.56.39.mp4?dl=0 Here temp is reached, but it does not seem to cool down and turn off.. Instead it stays ON and blows verly slowly. Same here: https://www.dropbox.com/s/10xymfh2a3asgbq/2014-11-29%2010.56.58.mp4?dl=0 https://www.dropbox.com/s/r...

In this video, flae is OK and burner should be working on HIGH setting , but it is obvious it is not as strong as it should be. At about 10 sec. after the beginning the speed drops almost to 0 and then resumes.. at sec 41 - same thing - why? https://www.dropbox.com/s/ds5xi4gcucvm9p2/2014-11-29%2012....

Hello, Hope for some help in english. The burner worked fine last year (on CTC 1100). This year on the second day of operation there was some strange behaveor which I did not notice before. Set on HIGH settings the fan was working quite low.. if I switch to Low - no difference (same speed of Fan). T...

By the way, someone might give me ideas about the pellet burner settings? I think it should reach the temps easy, but it struggles. In EL. it is only 16.7 kW and it has no problems, in pellets it should be 25 kW, but it cannot reach 65-70C in temps below 5C although it burns non-stop. The burner cha...

Unfortunately there are 0 intiatives by our government.. Not for heating, not even for electrical cars for example :) Anyway, I think electricity and oil will be roughly the same price.. however if you program the heating to be more in night tariff and less during the day, it might be less with elec...

I have set the wheel to minimum.. should be 10 Pa. Tomorrow or after tomorrow I will make small video of the whole setup and the starting procedure. I think the ..matarskruv gives pellets a little irregularry.. tometimes it turns but nothing falls sometimes a little .. sometimes more. Just a while a...

I still have problems with starting up.

It almost starts.. and sometims it fires at the last moment ..as soon as it gives up..

Could it be due to the pellets. Almost all pellets sold here are 6 mm. I read in the manual it is for 8 mm..

Could this be the problem?

Thx,

That's exactly what I did 1bour ago (the switch for the draught).

I do have a draught regulator installed.

I'll see how it holds now with the other setting.

Thank you

Hm, we still have failed starts from time to time..

Sometimes it fails with just cleaned grate... sometimes it works flawlessly for 2 days..

Is there a setting for the air (fan strenght) during ignitions?

Or maybe I need a new heating element?

Thank you.

All is working just fine after the increase of the inital dose.

How often should I clean it? I know it depends on the pellets, but is there some kind of way to know it is time to clean?

Thx